In times past garage doors could only be lifted by grabbing the handle at the bottom of the door and lift up to open it and to shut it you repeated the steps. Today, in order to open a garage door repair La Flintridge CA, you need some type of opener, which was invented in the 1920's. They can be opened by a remote control or from a switch on the garage wall. There are several different garage door openers on the market. Belt drive This opener is not as noisy as the chain drive. They can be installed for a garage that is below or next to the home. This opener is more durable and stronger than the chair drive, which is why many people prefer this one. The unit of this opener consists of a rubber belt instead of a steel chain. Chain drive This one is the cheapest and one most commonly used. It is very easy to install this device because it is basically a metal chain connected to the motor of the opener. You can activate it with a remote control or switch. To lift the garage door up when the main switch is turned on the opener uses a shaft and sprocket chain. This is the noisiest type of garage door opener made. C. G. Johnson made the first types of these openers. Normally the switch is installed on the garage wall for better access, both on the outside and the inside. Screw Drive This was founded by a manufacturer called Genie and is an automatic opener. A motor called direct driver operates it. The garage door is lifted with the help of a threaded steel rod. It moves when the motor is switched on using no belts or chains so there is no noise at all. It also has more speed than the other two types of garage door openers making it more efficient, When choosing a door opener for you garage look at the power you are going to need. If you are opening a single door, a smaller motor will work but if you have a double door garage you will need a motor with at least one-half horsepower. You should look for one that offers a safety mechanism that will keep the garage from closing all the way if something is in the electronic beam that stops the door from closing, helping to prevent accidents that could be serious, even fatal. Another safety feature you might consider is a rolling code. This changes the opening signal each time you activate the door. This will prevent crossed signals with your neighbor's garage door and protects your security code. Look for the simplest one that fits your need. Article Source
0 Comments
Although most men feel like they can fix anything, this tends to be proven wrong more often than not. Whether it's the leaky faucet, a clogged toilet or even an electrical problem, men everywhere promise they can fix it but leave their wives disappointed and on the phone calling a technician. Fixing a garage door is no easy task and something that you should leave up to a professional. Here are a few details about garage repairs so you will know what you are talking about when you call a garage door repair Wheat Ridge CO, service company.
There are three main mechanisms of a garage door that could need to be repaired. The motor, the door itself, or the springs. These are the most common types of garage door repairs people have to make they are all very important pieces that allow your door to open and close. If you are having trouble with your garage door opening or closing, there are a few things to check right off the bat. First, make sure the motor on your door is plugged in. If it is plugged in, try plugging something else into the same outlet to ensure the circuit has not been tripped. Second, check to make sure the sensors have not been bumped or something is not blocking them. The two garage sensors must point at each other, a red dot will verify they have not been bumped. Third, check to make sure the metal track your door runs up and down and the wall brackets are tightly secured to the wall. Last, you will need to check on the springs. Check both springs and make sure the tension is tight on both. If one is broken, do not attempt to fix on your own. There is a risk of the spring snapping leaving your garage door to come crashing down on you or your possessions. Leave the spring repair to a technician who has experience replacing them. As heavy as a door can be, you do not want to be responsible or get hurt. Article Source: http://EzineArticles.com/3814299 When you have broken garage door springs that need to be repaired you can either call a professional to repair them or you can do them yourself. These springs are long and heavy and are what is used to raise and lower your garage door. If you have broken spring repairs that need to be taken care of here are the steps that you can follow to get the repair job finished. Following the steps will help to ensure that the job can be done easily. The most important step that a person needs to remember is to make sure that you have turned off the power to the garage door so you do not get electrocuted while making the repairs. You need to make sure that you disconnect garage door opener power cord along with disconnecting it from your garage door. This is for the newer doors installed in the garage as with the older versions you may need to remove the fuse or turn off the circuit break to turn off the power. Look closely at the broken garage door spring and the new one to make sure that they are both the same. You need to check both of them to make sure that they are the same type and dimensions. When you are picking up the garage springs avoid grabbing them by the spring. You also need to make sure that you do not touch the winding cones on the new spring. You need to take a marker or some other type of writing instrument to mark the torsion shaft ends. You need to do this because it helps you to make sure you have garage doors that are level when you have finished the broken spring repairs and installed the unbroken springs. Wind the unbroken spring off and unfasten the bolts securing the torsion cones and spring bracket together, and then remove the bolts. Once you have completed this step in your broken spring repair project it is time to replace the spring along with re-install the hardware. Once you have this done it is time to wind up the new springs. Once you have completed this step you need to check to make sure that the garage door's balance to see if it is level. In order to minimize the friction you may need to apply some lubricant. After you have checked to make sure the door is balance and all things are tight and in place it is time to reconnect the door opener again. Although you have heard that you should not play with a garage door and the opener you need to open and shut it a few times to make sure it is functioning properly. It is easy to fix your garage door broken spring repairs on your own but you do need to make sure that you are doing it very carefully because it can be a dangerous repair job if not done correctly and you need an experts in garage door repair North Hills CA. You could lose your hands, limbs, fingers, or even your life. Article Source: http://EzineArticles.com/7712693 Garage doors are often the most overlooked part of any household. A number of US homeowners, in some of the major cities like Oahu and Pearl City, do not prefer even to spend a minute on checking their carport gates for possible damages. If these heavy structures are checked on a regular basis then it would help avoid any major technical defect in the future. It is also true that timely repairs can increase the life span of these gates. Garage doors are used frequently. They have to move up and down numerous times in a single day. This would result in wear and tear of these heavy structures, so lack of proper repair may ultimately make these gates unusable. It is always better to hire a company which deals in garage door service to perform all the necessary repair work of your garage door. There are numerous parts of these heavy structures which may require repair. Here are some tips to understand when these parts may need a repair: Gate tracks: Since your garage door is frequently used, there are high chances that the tracks of these structures may get damaged. If the gate does not move properly then it may mean there is something wrong with the tracks. In case it is a minor damage then with the help of a hammer you can pound them back in shape. However, if it is a major damage then you may have to get them replaced. Most homeowners, in US cities like Oahu and Makaha, prefer to hire a technician to do the repair work of the tracks in case of any serious damage. Springs: If you are checking your garage gate, then ensure to check the springs also. This is important especially if you have a roll up garage. Most of the times these springs need to be readjusted. However, it is important to know that it is always better to let an expert who deals in garage door service do the repair work of the springs, since these are dangerous if dealt with by a person who knows nothing about the technicalities. Article Source: http://EzineArticles.com/5772944 Most of us believe that garage doors are simple from beginning to end. After all, how hard is it to have a door that you can roll up? It seems simple, but, in fact, it definitely is not. Garage doors work by having a perfect blend of items, including springs and rollers, which allow the heavy door to lift gently. And if your garage door stops working, you may suddenly wonder how you're going to get your door to work again, or if you're going to have to purchase a whole new door. Quite often the purchase of a new garage door can be avoided by changing up a few things, and one of those things is the springs. Garage doors have two different types of springs. One is known as torsion springs, and the other is extension springs. Both of these springs are used to counterbalance the weight of the garage door, allowing you to easily lift something that should be too heavy for the average person to lift. How can you tell which type of spring you have? Look directly above the garage door. If you've got a spring that stretches and contracts as the door opens and closes, and that is mounted above the horizontal tracts, you have an extension spring. If, however, you've got a spring that is mounted on the bar that is directly above the door and that winds and unwinds as the garage door opens and closes, you've got a torsion spring. If you need to change out your torsion springs for your garage door, you first need to know how to find the right one. Unfortunately, all torsion springs aren't the same, and buying the wrong one will give you nothing but grief. There are four dimensions that determine how much the spring can lift. The first is the length of the torsion spring. This can be easily measured. The next is the inside diameter. This can also be fairly easily measured using your tape measure. Next is the wire size, which needs to be measured, and finally is what is known as wind. This can all get very confusing, which is why many people choose to purchase the same type of torsion spring that came with their garage door. You can find what type of torsion spring your door uses fairly easily online, using a search engine or a site that specializes in selling torsion springs. Replacing any type of spring on a garage door can be a dangerous proposition, as the springs are under tension. If you don't use the correct tools and are not careful, injuries may occur. Make sure, before you do any changing of the springs on your own, that you have read how to do it and that you are using the right tools in a very safe manner. Changing torsion springs can be tricky so calling a qualified professional garage door service company is always a good idea. Article Source: http://EzineArticles.com/3051525 The use of home garages is no longer confined to simple car parking or storage of unused items. They are now essential additions to houses and serve multiple purposes. Because of their increased value, garages now require more careful maintenance. One of the most common aspects of this maintenance is garage door repair. This is particularly true not only because garages are prone to damage but also because owners cannot afford these parts of the garage to remain broken. While garage repair is an essential maintenance procedure, there are some steps that need to precede it. In particular, there are preparations that you should take before engaging in the repair. Here are some of them. Learning the Mechanics Repairing a garage door cannot be possible if you do not fully understand its parts and mechanism. This is why the first step in preparing for this repair is to learn the fundamentals. You must learn the different parts of the door, which can be generally classified as either a moving or a non-moving part. In broad terms, though, the door can be broken down into two major parts: the opener and the actual door. Aside from this, you must also be familiar with the mechanics of the door, which involve the rolling of the door on metal tracks through the aid of heavy springs. Understanding the specific details of this mechanism may be necessary for some cases of garage repair. Examining the Tracks After getting to know the fundamental concepts of the garage door, the next step is to check the door for issues. To begin, you should examine the tracks to which the actual door rolls on. One important aspect to evaluate is the condition of the mounting brackets. If these brackets are only loosely holding the tracks in place, then there is a need to tighten certain bolts. The tracks must then be checked for malformations and dents. In addition, you need to determine if the tracks are leveled and perfectly aligned. You should also look for dirt, grease, and any debris that may cause an obstruction along the tracks. Finally, the lubrication of the tracks must be examined. If closing or opening the garage door causes a creaking sound, then that is an indication that the tracks need to be lubricated. Checking the Hardware Once the condition of the tracks has been evaluated, it is time to check the other mechanical parts of the garage door. In particular, you need to pay attention to the springs and hinges. You need to check whether or not these parts are tightly wound. If either side of the door is sagging, then that is a sign that the hinges are loose. The springs are meanwhile loose if the garage door does not open or close completely. On the other hand, enlarged screw holes are an indication that the bolts are not tightly fitted to their respective places. This issue can be remedied by replacing the old screws with larger ones so that the enlarged space can be filled appropriately. A technician at Garage Door Repair, will gladly help you with this. Article Source: http://EzineArticles.com/8400525 Before the snow comes blowing in, it is important to clean and maintain your garage doors. This would ensure that the door would be in tiptop condition and any problems can be prevented. By taking the time to check, repair and clean the doors, this would not only make it easier for you, it would also prolong the life of the garage. Cleaning typically would involve the use of cleaners, rags and water. However, some special cleaning agent may be required depending on the type of door that is installed by the homeowner. Cleaning doors can be done once a year but for those who live near the sea or have high salt air climate, cleaning and maintenance should be more regular to ensure that the doors are free of dirt and functioning properly. Cleaning Steel Garages Steel doors are easy to clean and would only require mild cleaning agents or even household cleaners without bleach. Simply dissolve the cleaner or agent with room temperature water and wash the door using sponges or soft bristle brushes. This would remove any dirt or grime without removing the film that coats the door. Remember to rinse the soap from the door to prevent any residues that might damage the door's film and ruin its durability. Let the door dry completely before applying wax to coat and protect the door. There are some waxes that one might buy from stores or once could use car wax to coat the steel door. Cleaning Wood Garages Cleaning wood doors can be tricky as the water might penetrate the wood especially woods that have cracks on its surface. Before cleaning the door, ensure that it is in good condition. Regular cleaning and maintenance would prevent the door from being damaged and would help it last longer. To remove dirt or grime from the door, use a diluted solution of cleanser and water - one cup of concentrated household cleaner without bleach to five gallons of water. Scrub the surface and rinse thoroughly with clear water. Let it dry completely before applying finish coating to protect the wood. For damaged areas, use oil or primer to coat the wood substrate. Remember that aside from cleaning the garage door system, one should also check the door's condition. These would include checking the rollers, cable wires, hinges as well as checking the door's balance. Ensure that after cleaning the door thoroughly, the hinges or wires are dry as water can cause rust which can erode the hinges and upset the door's balance that might cause accidents. Article Source: http://EzineArticles.com/8710704 If there were one thing that can annoy you the most about a garage, it would have to be a noisy garage door. Not only can this cause disruption to sleep, work, or concentration, it can also be stressful especially if the living room or bedroom is located near the garage. If your door makes annoying squeaking noises and you can no longer endure it, do not worry, you don't have to suffer any much longer. With these practical tips, you can finally make the garage door shut up and you can have the peace and quiet you've always wanted. Check for loose nuts One possible cause for a noisy garage door would be loose nuts. Using a socket wrench or an adjustable wrench, tighten all the nuts on the door and track. Just make sure that you do not over tighten it. If you are not confident about your handy skills, have someone who is to do this job. Buy new rollers Metal rollers begin to make noise when they get old and worn out. To determine if this is the cause of the problem, open the door and identify if the rollers are making noise while they roll and up and down. If yes, consider replacing them. Opt for nylon rollers Nylon rollers are much quieter than metal rollers. Not only that, they also don't have to be lubricated all the time. This is a good choice if you don't mind the extra cost, as this type of rollers is more expensive. Install new hinges The hole in the hinge that holds the roller stem eventually becomes worn out. Check each of the hinges on both sides and replace them if the hole has become more oblong than round. Buy a new garage door If all else fails, maybe you need an entirely new garage door. But before you go to the nearest home improvement store to do this, think carefully first if you really need one. If it is already old and worn out, you may want to replace with a newer model. New garage doors have updated safety features for maximum protection. Most of the new models of sectional, up and over, and roller garage doors have a safety emergency reverse feature that reverts the door to its original opened position when an object blocks its door path. This is important for the safety of your family, pets, and possessions. If you are feeling so stressed out lately and it is not about work or chores, it is probably because of the noisy door that has been keeping you wide awake for last few days or weeks. You don't have to endure this for long, as there are many things you can do to solve this problem. You can either fix the cause of the noise or replace your old worn out garage door with a new one. If you decide to go for the latter, see to it that you only rely on trusted brands and high quality products that will give utmost protection for you and your whole family. Article Source: http://EzineArticles.com/4459396 |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |